GoodWe was founded in 2010 and makes solar inverters and batteries, among other things. Its own warranty sends a claim to "the local distributor where the product was purchased, or the installer who installed the inverter". So the GoodWe price you see is the one your installer writes, and the only thing that makes two GoodWe quotes comparable is the model number.
That model number carries more weight here than the kilowatt figure in the product name, because GoodWe's single-phase hybrid range crosses an ESB Networks limit somewhere between 5 kW and 6 kW.
- Two single-phase families, one three-phase. ES G2 (3 to 6 kW) and ES Uniq (3 to 12 kW) are single phase and take a 48 V battery. ET G2 (6 to 15 kW) is three phase and takes a 150 to 720 V battery.
- The 5 kW clears the grid limit and the 6 kW does not. GoodWe's own spec sheet rates the GW6000-ES-20 at 27.3 A. ESB Networks, the body your installer files the grid connection with, will not take a unit tested above 25 A through its free route.
- Three phase is a separate limit. It is 16 amps. The 6 kW, 8 kW and 10 kW ET G2 clear it. The 12 kW and 15 kW do not.
- Ten years, but only on recent stock. GoodWe's EU warranty gives 10 years to residential hybrids produced on or after 1 January 2026, and 5 years to the same series produced before that date.
- The battery can cost you the inverter cover. Only batteries on GoodWe's published compatibility list are approved, and it reserves the right to treat damage from an incompatible pack as an out-of-warranty case.
The GoodWe Models You Will See on an Irish Quote
GoodWe's spec sheets split these units by phase and by battery voltage. That split is the first thing to pin down on a quote. It decides which grid limit applies to you, and which batteries can be paired with the unit.
| Series | What the spec sheet says it is |
|---|---|
| ES G2 (3 to 6 kW) | Single phase, 2 MPPTs, 48 V battery with a 40 to 60 V range |
| ES Uniq (3 to 12 kW) | Single phase, 1 or 2 MPPTs, 48 V battery, rated IP66 |
| ET G2 (6 to 15 kW) | Three phase, 2 or 3 MPPTs, 150 to 720 V battery |
| SBP G2 (3.6 to 6 kW) | AC-coupled retrofit, adds a battery to an existing PV system |
The ES G2 and the ES Uniq look similar on paper. The real difference is headroom. The ES G2 takes up to 16 A per MPPT, and its spec sheet puts one string of panels on each MPPT. GoodWe lists 7,500 W of panels as the most you can put on the 5 kW. The ES Uniq takes up to 20 A per string, allows 200% PV input oversizing, and runs to 12 kW. On a single-phase supply, most of that extra size is no use to you, for the reason below.
The 25 A Line Decides Whether Your Connection Is Free
ESB Networks defines a micro-generator by current rather than by kilowatts. It defines a micro-generator as a source of electrical energy rated up to and including 25 amps, about 6 kVA, at low voltage on a single-phase connection. It says plainly that there is no charge to connect, as long as the job goes through what it calls the "inform and fit" process. Stay inside that rating and your installer files the NC6 form and no grid charges arise.
The wording is the part that catches people. ESB Networks says that from 31 May 2023, any unit with a Rated Current as per Type Test over 25 A is not eligible under the NC6 route. So the figure that decides it is the Rated Current as per Type Test. It is not the kilowatt figure in the model name.
Put the GoodWe single-phase range beside that line. These are the Max. AC Current Output to Utility Grid figures from GoodWe's own spec sheets, not from a shop listing.
| Model | Nominal output power | Max. AC current output to grid | Against the 25 A NC6 ceiling |
|---|---|---|---|
| GW3000-ES-20 (ES G2) | 3,000 W | 13.6 A | Inside |
| GW3600-ES-20 (ES G2) | 3,680 W | 16.7 A | Inside |
| GW5000-ES-20 (ES G2) | 5,000 W | 22.7 A | Inside |
| GW6000-ES-20 (ES G2) | 6,000 W | 27.3 A | Above it |
| GW5000-ES-C10 (ES Uniq) | 5.0 kW | 25 A | At the limit |
| GW6000-ES-C10 (ES Uniq) | 6.0 kW | 30 A | Above it |
| GW8000-ES-C10 (ES Uniq) | 8.0 kW | 40 A | Well above it |
| GW12K-ES-C10 (ES Uniq) | 12.0 kW | 60 A | Well above it |
The 6 kW is the one to watch. "6 kW" sounds like it matches a 6 kVA allowance. It does not. The ES G2 version is rated 27.3 A and the ES Uniq version 30 A, both over the line ESB Networks drew. The 5 kW ES Uniq is awkward in a different way. At 25 A exactly it sits inside a ceiling ESB Networks words as "up to and including" 25 amps, with nothing to spare.
Ask which connection route the installer is applying under, and ask for the figure on the type test certificate. ESB Networks writes the rule against that tested current, so a brochure will not settle it, and it is not something to find out after the panels are up. More on sizing: maximum solar system size in Ireland.
Three Phase Has a Different Limit
If your house is on a three-phase supply, the 25 A figure is not your limit. ESB Networks sets the three-phase ceiling at 16 amps, about 11 kVA, on a three-phase connection. The ET G2 range sits either side of it.
| Model | Nominal output power | Max. AC current output to grid | Against the 16 A three-phase ceiling |
|---|---|---|---|
| GW6000-ET-20 | 6,000 W | 8.7 A | Inside |
| GW8000-ET-20 | 8,000 W | 11.6 A | Inside |
| GW10K-ET-20 | 10,000 W | 14.5 A | Inside |
| GW12K-ET-20 | 12,000 W | 17.4 A | Above it |
| GW15K-ET-20 | 15,000 W | 21.7 A | Above it |
Compare two figures from the spec sheets. The 10 kW three-phase ET G2 is rated at 14.5 A. The 6 kW single-phase ES G2 is rated at 27.3 A, for less power. That is why the phase question comes before the size question. The 12 kW and 15 kW ET G2 are rated at 17.4 A and 21.7 A, past the 16 amp ceiling.
What ESB Networks Actually Wants to See
ESB Networks says it has no function in qualifying equipment or installers.
What it does want is a standard and a certificate. The inverter must comply with IS EN 50549-1 with current Irish settings, and a type test certificate saying so must accompany the application form. So the useful thing to ask an installer is not "is this brand approved". It is "send me the IS EN 50549-1 type test certificate for this exact model, and tell me the rated current on it".
Ask as well which country setting the unit arrives on, and who switches it to the Irish one on the day, because the rule names current Irish settings specifically. More: solar inverters in Ireland.
Ten Years, But Only on Recent Stock
GoodWe's EU warranty document, Rev 4.0, applies to products installed on or after 17 September 2026. It splits the cover by the date the unit was made. That is unusual, and worth knowing before you compare quotes.
Residential hybrid inverters produced on or after 1 January 2026 get 10 years. The document names the series: ES G2, ES Uniq 3-12k, EH Plus+, ET 15-30k, ET Plus+, ET G2, ET LV, SBP G2, ESA 3-10k and ESA 5-30k. The same hybrid series produced before 1 January 2026 get 5 years. So two units with the same model number on the box can carry different cover, depending on when each was made.
When the clock starts is the other detail. The warranty period runs from whichever comes first: the day the unit was installed, or 12 months after the day it was made. A unit that sat in a warehouse for more than a year has already spent some of its term before it reaches your wall. So the date it was made is a fair thing to ask for.
GoodWe sells a warranty extension through its authorised distributors and its own online channel. It also says the warranty will be automatically extended to 10 years where a set of conditions is met. Those conditions all have to hold at once. The inverter has to run a GoodWe Lynx battery, first used between 15 May 2023 and 31 December 2026. It has to be linked to the SEMS+ app, with generation data uploaded. It has to be produced after 1 January 2021. It has to be fitted by an installer qualified as a GoodWe PLUS+ installer in the EU, the UK, Switzerland or Norway. And both the inverter and battery serial numbers have to be registered. That is a chain of five conditions. An ordinary job can miss any one of them quietly.
Two limits on what the cover is worth. GoodWe says the warranty covers only the cost of the hardware needed to get the unit working again. It says it will cover transport costs up to a set amount per case, and that it may offer a rebate towards on-site labour at its sole discretion. Electricity you did not generate during the downtime is not covered at all. A claim also has to be made no later than 1 month from the date the fault first appeared, or the rights under the warranty expire. So a fault you spot and leave until the next annual service is one you may end up paying for.
GoodWe's EU warranty applies to units originally bought through channels it authorised and installed within the EU, UK, Norway or Switzerland. For a unit sold for one country and installed in another, it states the warranty becomes invalid without written approval from GoodWe before installation. So an inverter bought cheaply from outside those channels can arrive with no manufacturer cover. More: DIY solar panels in Ireland.
The Battery You Pair It With Can Cost You the Inverter Cover
GoodWe publishes a battery compatibility document and states that only batteries listed in it are approved for connection to GoodWe storage inverters under the GoodWe limited warranty. Its warranty terms then add the consequence: for inverter damage caused by using a battery pack that is not compatible, GoodWe reserves the right to deal with the claim as an out-of-warranty case.
The list is a long one, so this is a paperwork problem rather than a lock-in problem. The low-voltage inverters, which is where the ES G2 and the SBP G2 sit, pair with GoodWe's own Lynx Home U and Lynx Home A, and with listed packs from battery makers including BYD, LG, Pylontech and Dyness. The higher-voltage ET G2 pairs with Lynx Home F, Lynx Home F G2 and Lynx D G2, and with listed BYD, Pylontech and Dyness towers. The list goes down to the inverter series, and sometimes to the firmware version. So "the brand is on the list" is not the same thing as "this model is listed for this inverter".
Get the battery make and exact model written on the quote, and ask the installer to confirm it appears in GoodWe's compatibility document for that specific inverter series. On size, SEAI's separate €600 battery grant needs 5 kWh or more. More: battery storage in Ireland and the solar battery grant.
What the SEAI Grant Does and Does Not Care About
SEAI pays €700 per kWp for the first 2 kWp and €200 for every extra kWp up to 4 kWp, capped at €1,800. The whole grant is worked out on panel capacity in kWp. SEAI states that it does not approve, guarantee or warranty a company or their works. What it does require is an SEAI-registered company and a house built and occupied before 2025, and it pays the grant into your nominated bank account.
Since the grant is worked out on panel capacity, a 4 kWp array draws the €1,800 whichever inverter sits behind it. A battery of 5 kWh or more draws the separate €600, bringing the combined maximum to €2,400. You have 8 months from approval to get the works done.
The grant does join up with everything above at one point. SEAI makes the solar company responsible for sending the NC6 form to ESB Networks, and it lists that completed form among the documents needed before the grant is paid. So the completed NC6 form is on SEAI's document list either way, which ties your connection route to the grant paperwork. More: the SEAI solar grant and the registered installer requirement.
Why There Is No Price on This Page
GoodWe's warranty sends buyers to the distributor they bought from or the installer who fitted the unit. Quoting a figure from a UK shop or a forum thread would be inventing a market price, so we will not.
What you can do is make the quotes comparable. Ask every installer for five things: the exact GoodWe model number, the tested rated current, the date the unit was made, the battery make and model with confirmation it is on GoodWe's list, and whether they are GoodWe PLUS+ qualified. With those answers, the cheapest quote is a fact rather than a guess. More: how to vet a solar installer.
And remember what happens to the power you do not use. ESB Networks says it is not responsible for buying or selling electricity, that this is a matter between you and your electricity supplier, and that the Commission for Regulation of Utilities sets who qualifies for export payments. More: Clean Export Guarantee rates and micro-generation in Ireland.
Frequently Asked Questions
Which GoodWe model fits the ESB Networks limit?
On a single-phase supply, the 3 kW to 5 kW units. GoodWe's spec sheets rate the GW5000-ES-20 at 22.7 A, the GW3600-ES-20 at 16.7 A and the GW3000-ES-20 at 13.6 A, all inside the 25 A ceiling for the free NC6 route. The GW6000-ES-20 is rated 27.3 A and the ES Uniq GW6000-ES-C10 is 30 A, both above it. On three phase the limit is 16 amps. The 6 kW, 8 kW and 10 kW ET G2 clear it at 8.7 A, 11.6 A and 14.5 A. The 12 kW and 15 kW do not, at 17.4 A and 21.7 A.
What warranty do GoodWe inverters come with in Ireland?
It depends on when the unit was made. GoodWe's EU limited warranty Rev 4.0 gives 10 years to residential hybrid inverters produced on or after 1 January 2026. The series named include the ES G2, ES Uniq 3-12k, ET G2 and SBP G2. The same series produced before that date get 5 years. The period runs from the earlier of first installation or 12 months after production. So ask for the manufacture date as well as the term.
Can I get 10 years on a GoodWe inverter that only has 5?
GoodWe publishes an automatic extension to 10 years, but every condition has to hold at once: a GoodWe Lynx battery first operated between 15 May 2023 and 31 December 2026, the inverter connected to the SEMS+ app with generation data uploaded, production after 1 January 2021, installation by a GoodWe PLUS+ qualified installer in the EU, UK, Switzerland or Norway, and both inverter and battery serial numbers registered. Ask the installer to confirm each one rather than assuming it is automatic.
Can I buy a GoodWe inverter direct in Ireland?
No. GoodWe's warranty routes a claim to the local distributor where the product was purchased, or the installer who installed the inverter.
Which batteries work with a GoodWe hybrid inverter?
Those on GoodWe's published compatibility document, which it says lists the only batteries approved for connection under its limited warranty. The low-voltage inverters, including the ES G2 and SBP G2, pair with GoodWe's Lynx Home U and Lynx Home A and with listed packs from BYD, LG, Pylontech and Dyness. The higher-voltage ET G2 pairs with Lynx Home F, Lynx Home F G2, Lynx D G2 and listed BYD, Pylontech and Dyness towers. Compatibility is recorded per inverter series and sometimes per firmware version, so get the exact model confirmed rather than the brand.
Is an inverter "ESB approved" in Ireland?
No, and no inverter is. ESB Networks states it has no function in qualifying equipment or installers. What it requires is that the inverter complies with IS EN 50549-1 with current Irish settings, and that a type test certificate stating that compliance accompanies the NC6 application. Ask for that certificate for the exact model on your quote.
Does the SEAI grant cover a GoodWe inverter?
Not specifically, and no grant covers any inverter brand by name. The grant pays €700 per kWp for the first 2 kWp and €200 per additional kWp up to 4 kWp, capped at €1,800, calculated entirely on panel capacity. SEAI requires an SEAI-registered company and a house built and occupied before 2025, and states it does not approve, guarantee or warranty a company or their works. A battery of 5 kWh or more draws a separate €600.
What is the difference between the GoodWe ES G2 and the ES Uniq?
Both are single-phase hybrids running a nominal 48 V battery, and the difference is headroom. The ES G2 covers 3 to 6 kW, takes up to 16 A per MPPT and lists 7,500 W of maximum PV input on the 5 kW unit. The ES Uniq covers 3 to 12 kW, takes up to 20 A per string, advertises 200% PV input oversizing and is rated IP66. On a single-phase Irish connection, the extra size the ES Uniq offers is mostly unusable under the 25 A limit.
Can I add a GoodWe to panels I already have?
Yes. The SBP G2 is an AC-coupled retrofit inverter rated 3.6 to 6 kW, designed to add a battery to an existing grid-tied array without replacing the inverter already on the wall. It appears on GoodWe's low-voltage battery compatibility list alongside the ES G2, so the same battery checks apply.
Published: 10 November 2026. Author: Neil Russell. GoodWe's founding in 2010, its 0.7kW to 350kW inverter range and its product portfolio of inverters, batteries, PV building materials, EV chargers, heat pumps and smart energy management systems are from its company profile.
Three GoodWe spec sheets carry the model figures. The ES G2 Series spec sheet gives the 3 to 6 kW single-phase range and its 2 MPPTs. It gives the grid output figures of 13.6 A, 16.7 A, 22.7 A and 27.3 A. It gives the nominal output power of 3000 W, 3680 W, 5000 W and 6000 W. It also gives the 48 V battery, the 40 to 60 V range, the 16 A per MPPT input and the 7,500 W maximum PV input on the 5 kW unit.
The ES Uniq Series spec sheet gives the 3 to 12 kW range and its 1 or 2 MPPTs. It gives the grid output figures of 15 A, 18 A, 25 A, 30 A, 40 A, 50 A and 60 A. It also gives the 20 A per string input, the 200% PV input oversizing and the IP66 rating.
The ET G2 Series spec sheet gives the 6 to 15 kW three-phase range and its 2 or 3 MPPTs. It gives the grid output figures of 8.7 A, 11.6 A, 14.5 A, 17.4 A and 21.7 A. It also gives the nominal output power of 6000 W to 15000 W and the 150 to 720 V battery range. The SBP G2 retrofit inverter and its 3.6 to 6 kW rating are from GoodWe's SBP G2 Series page.
The warranty terms are from GOODWE Limited Warranty for Inverter System in Europe Rev 4.0. That document sets the 10-year and 5-year terms, split on 1 January 2026 production. It names the hybrid series each term covers. It starts the warranty period from the earlier of first installation or 12 months after production. It sets the 1-month claim deadline. It limits cover to hardware material and excludes lost generation. It sets the EU, UK, Norway and Switzerland scope. It voids a unit installed outside its intended country without written approval. It lists the five conditions of the automatic 10-year extension, and the separate extension that can be purchased. It sets the transport cost cover and the discretionary on-site labour rebate. It routes claims to the local distributor or installer. And it is effective for products installed on or after 17 September 2026.
The battery pairings are from GoodWe's Battery Compatibility Overview. It states that only listed batteries are approved under the limited warranty. It lists the Lynx Home U, Lynx Home A, Lynx Home F, Lynx Home F G2 and Lynx D G2 packs, and packs from BYD, LG, Pylontech and Dyness. It sorts them into low-voltage and high-voltage tables, with an SBP G2 column beside the ES G2 one. The out-of-warranty treatment of damage from an incompatible battery is from the warranty document above.
The grid rules are from the ESB Networks page on connecting a home generator. It sets the 25 amp and about 6 kVA single-phase limit. It sets the 16 amp and about 11 kVA three-phase limit. It confirms there is no connection charge under "inform and fit". It states that from 31 May 2023, any unit with a Rated Current as per Type Test over 25 A is not eligible under NC6. It requires compliance with IS EN 50549-1 with current Irish settings, with a type test certificate accompanying the application. It states that ESB Networks have no function in qualifying equipment or installers. And it says ESB Networks DAC are not responsible for the purchase or sale of any electricity, that this is a matter for a customer and their supplier, and that the Commission for Regulation of Utilities sets export payment eligibility.
The grant figures are from SEAI's Solar electricity grant page. It sets the €700 per kWp to 2 kWp and €200 per additional kWp to 4 kWp tiers. It sets the €1,800 cap, the €600 battery grant for 5 kWh or more, and the €2,400 combined maximum. It sets the built and occupied before 2025 condition. It requires an SEAI-registered company. It states that SEAI does not approve, guarantee or warranty a company or their works. It makes the solar PV company responsible for submitting the NC6 form. And it sets the 8-month completion window and payment into your nominated bank account. All sources were verified live on 10 November 2026. No installed price is quoted, because neither GoodWe nor any Irish distributor publishes one.
The only way to know whether a GoodWe quote is good is to see two more. Get quotes from SEAI-registered installers near you, ask each one for the exact model number, the type-tested rated current and the date of manufacture, and compare the warranty terms as well as the totals.
Get a Solar Quote →